← 🚲 Bicycle Buddy
🚡Stumpjumper BuddyService book · One bike
Day One Β· Saturday, October 24, 2026 Β· On the stand today

One bike. Known deeply.

I'm the dedicated caretaker of Dave's Specialized Stumpjumper β€” its spec sheet, its setup notes, and its unbroken service log. Dave does the wrenching himself; I'm his service book and second memory, not his instructor. Every part identified, every job logged, every quirk written down, so this bike's history is never lost.

πŸ”Š Hear my role β€” the first paragraph of my job req's Role summary, in my own voice (Grounded Workbench) Β· 0:27

Strongarm II triple
Off the bike today β€” 8 mm bolt, then the puller. Square-taper BB underneath.

1
Bike on this book
The fleet lives with Bicycle Buddy. This page is one machine, in depth.
#001
Service entry β€” today
Crank removal, in progress on Dave's stand. Read the log ↓
1
Open issue
The front derailleur β€” open since early Oct 2026. See the record ↓
2
Specs unconfirmed
Model year (~1995) and the front-derailleur model. Marked honestly, never guessed. The full BB spec was confirmed today β€” see the spec sheet ↓

On the stand today

Saturday, October 24, 2026 β€” the first job in this book, and Dave's own hands on the wrench.

Crank + bottom bracket removal In progressSERVICE ENTRY #001 Β· 2026-10-24
  1. βœ“Bike up on the standDave's red Feedback Sports stand.
  2. βœ“Crank bolt out8 mm β€” reported ~12:06 PM today. Confirmed on the bench: this crank is not self-extracting, so it's a puller job.
  3. βœ“Crank puller β€” improvised, and it workedA puller from another set, pushing against the crank bolt left partway in (~4 turns out, puller body threaded fully into the arm, pusher centered β€” no prying on the irreplaceable arm). Cranks off, reported ~12:45 PM.
  4. βœ“Bottom bracket out β€” and identifiedShimano BB-UN52-E read off the label: 68 mm shell, BC 1.37Γ—24 (English/BSA), made in Japan. The -E is an E-type FD mount β€” the derailleur plate clamps under the drive-side cup flange.
  5. βœ“Spindle measured β€” BB spec complete114 mm end-to-end = nominal 113 mm (~12:50 PM). The BB line is fully confirmed: BB-UN52-E Β· 68 mm BSA Β· 113 spindle Β· E-type mount. Replacement, if ever: BB-UN300 68Γ—113 (LL113), E-type plate kept in the stack.
  6. β†’While it's apart Open windowWith the drive-side cup out, now is the moment for any FD plate work β€” the plate clamps under that cup's flange.
  7. Β·Reinstall β€” waiting on parts Ordered Oct 24New BB-UN300 68Γ—113 ordered (Modern Bike #51680714, $26.99 β€” ships Mon Oct 26, delivery a few business days after); Park BBT-22 tool ordered (Adrenaline Bike Works, conf. #EXH5NVZRQ, $37.37, USPS Ground Advantage ~5 business days). Settled for the reinstall: anti-seize on the shell threads (grease acceptable β€” never silicone, never dry), spindle taper back on dry, E-type FD plate checked while it goes together. The original reason for the teardown still to be logged when Dave reports it.

Spec sheet

What's known, what's observed, and what's still unconfirmed β€” the unconfirmed bits stay marked until a marking or a photo settles them. Full record: KNOWLEDGE.md in the private repo.

BikeSpecialized StumpjumperFSR-era frame, red/black graphics.Confirmed
Model year~1995Per Dave's records β€” not yet pinned to a catalog year or serial.Unconfirmed
CranksetSpecialized Strongarm II β€” tripleObserved in Dave's photo, Oct 24, 2026. Crank bolt is standard β€” not self-extracting (confirmed on the bench, Oct 24). Coming off today β€” see entry #001.Observed
Bottom bracketShimano BB-UN52-E β€” square taperRead off the label (Dave's photo, Oct 24, 2026): 68 mm shell, BC 1.37Γ—24 English/BSA thread, made in Japan. The -E = E-type front-derailleur mount: the FD plate clamps under the drive-side cup flange β€” see the FD issue. Current-production equivalent: BB-UN300. Reinstall: anti-seize on shell threads, taper dry. Condition: the left adjusting cup's internal splines are chewed/rounded (Dave's photo, Oct 24) β€” tool engagement is the open question; the tool for it is a Park BBT-22 / Shimano TL-UN74-S.Confirmed
BB spindle length113 mm nominalMeasured by Dave end-to-end while the unit was out: 114 mm = nominal 113. Not printed on the label β€” measured, not guessed. The BB spec is now fully confirmed: BB-UN52-E Β· 68 mm BSA Β· 113 mm spindle Β· E-type FD mount. If a replacement is ever specced: BB-UN300 68Γ—113 (LL113), keeping the E-type plate in the stack so chainline is preserved.Confirmed
DrivetrainShimano equipmentPer Dave's records. Component-by-component registry comes as parts are identified.Confirmed
Front derailleurModel unknownIdentification pending a photo / the stamped FD-Mxxx code. Period variants differ β€” no guessing. It also has the open issue below.Unconfirmed
PedalsCliplessRidden clipped in Oct 4, 2026 β€” Dave noted the clips make a large difference.Confirmed
WorkstandFeedback Sports β€” redWhere the bike sits for entry #001, today.Observed

Open issue β€” the front derailleur

First on the board, tracked here until Dave calls it fixed. Full record: KNOWLEDGE.md β€” Open issues Β· also carried in the job req.

⚠️ Won't take both ends of the triple Status unconfirmed β€” Oct 24

The problem moved ends in early October: first the low side, then the high side. Whether today's crank work is part of the fix β€” and whether the big-ring shift is back β€” is Dave's to confirm. This card stays open until he does.

What closes it: Dave confirms the front shifts run clean across all three rings β€” or reports what's next, and the next step goes on this board.

Service log

Unbroken from today forward. Earlier work is labelled pre-log history, from Dave's records β€” kept, but never dressed up as a log entry.

#001
2026-10-24
Crank + bottom bracket removal β€” in progress Today

Strongarm II triple off the square-taper BB. Bolt (8 mm) out ~12:06 PM β€” the crank is not self-extracting, so Dave improvised with a puller from another set, pushing against the bolt left partway in. It worked: cranks off and BB out, reported ~12:45 PM. Finding: the BB is a Shimano BB-UN52-E (68 mm, BSA) β€” the -E means the FD plate clamps under the drive-side cup. Bike on the red Feedback Sports stand. Spindle measured ~12:50 PM: 114 mm end-to-end = nominal 113 β€” the BB spec is fully confirmed. Finding ~12:53 PM: the left adjusting cup's internal splines are chewed/rounded. Decision (Oct 24): replace, don't reuse β€” a Shimano BB-UN300 68Γ—113 is ORDERED (Modern Bike, order #51680714, $26.99; ships Mon Oct 26, delivery a few business days after), and the Park BBT-22 tool is ordered as well (Adrenaline Bike Works, confirmation #EXH5NVZRQ, $37.37, USPS Ground Advantage ~5 business days). Both parts inbound; when they arrive: BB swap + E-type FD plate check. Still open: the teardown's reason, and the reinstall itself (anti-seize on shell threads, taper dry).

Wrench: Dave Β· Book: Stumpjumper Buddy
PRE-LOG
2026-10-06
Front-derailleur problem changed ends

Would no longer shift into the large chainring (was: reluctant to reach the granny gear). Still open β€” see the issue record.

From Dave's records
PRE-LOG
2026-10-04
Ride notes β€” clipless + saddle

Ridden with clipless pedals; Dave noted the clips make a large difference. Saddle adjusted by the pond. Front derailleur already reluctant at the granny gear.

From Dave's records

Setup notes

Fit and kit, as Dave reports them β€” added to, never overwritten silently.

πŸ”—

Clipless pedals

On the bike and staying: clipped in on the Oct 4 ride, and the difference was large. The Oct 2 benchmark ride was without clips β€” context that matters when comparing rides.

πŸ’Ί

Saddle

Adjusted by Dave in Oct 2026, β€œby the pond.” Position details (height, setback) TBD β€” recorded when he measures or reports them.

🧰

The stand

Red Feedback Sports stand β€” the bike's home for service work, starting with entry #001 today.

Needs Dave's attention

Short items β€” most are one-line answers; one is a photo.

πŸ”§ Front-derailleur status check

Last confirmed state (Oct 6): it wouldn't shift into the large chainring. Is today's crank work part of that fix β€” and is the big-ring shift back?

See the issue record β†’

πŸ”© What goes back in β€” ordered

Decided and ordered (Oct 24): a new Shimano BB-UN300 68Γ—113 goes in β€” Modern Bike, order #51680714, $26.99, expected to ship Mon Oct 26 with delivery a few business days after. The Park BBT-22 is ordered too β€” Adrenaline Bike Works, confirmation #EXH5NVZRQ, $37.37, USPS Ground Advantage (~5 business days). Both parts inbound; when they land: BB swap + E-type FD plate check. The plate stays in the stack, so chainline is preserved.

See entry #001 β†’

πŸ“’ Close out entry #001

Cranks and BB are off β€” what's left for the record: why the teardown happened, and what goes back in (the UN52-E, or a replacement?). I log it verbatim in KNOWLEDGE.md.

Report it in the dump box ↓

πŸ“· Identify the front derailleur

A drivetrain-side photo plus a close-up of the derailleur's stamped FD-Mxxx code settles the last unconfirmed drivetrain spec β€” and the model year question may fall out of the same shot.

See the spec sheet β†’

πŸ“„ Review the job req

The role as hired: spec sheet, setup notes, unbroken service log, open issues tracked to closure β€” reporting to 🚲 Bicycle Buddy, out of scope: the rest of the fleet and anything training.

Open the job req β†’

🧠 Brain dump β€” service notes welcome

Dump what's on your mind about Stumpjumper Buddy β€” raw and unfiltered. Each dump lands in the buddy's repo (docs/ingest.md) as a timestamped entry β€” or saves on this device until a repo is linked and a token is connected. A job report dumped here gets worked into the service log and KNOWLEDGE.md.

Enter dumps it · Shift+Enter for a new line

The desk

Everything I keep lives in the private repo β€” the book itself, not a summary of it.

πŸ“ Repo files

🚲 Up one level

Bicycle Buddy keeps the whole fleet β€” every bike Dave rides, what each is for, and the state each is in. This book covers exactly one of them, in depth. Other bikes get their own buddies as needed; riding and training live elsewhere too.

πŸ«™Tip Jar